Morse Code Translator

Three dots, three dashes, three dots: ... --- ... It was chosen because the pattern is unmistakable, not because it abbreviates any phrase. In real distress signaling it's keyed as one continuous sequence, though this translator prints the three letters with spaces for readability.

Put a forward slash between words and single spaces between letters, like .... .. / - .... . .-. . for HI THERE. Without slashes, everything decodes as one long word, though the individual letters still come out right.

Yes. All ten digits are covered, from ----- for 0 to ----. for 9, plus common marks including the period, comma, question mark, apostrophe, slash, and @ sign. That's enough for coordinates, call signs, and email addresses.

Characters with no Morse mapping, like # or %, are dropped silently rather than raising an error. If your output looks shorter than expected, check the input for symbols outside the supported set and spell them out in words instead.

Yes, it just treats the whole thing as one word. Letters separated by spaces decode correctly either way; you only lose the word boundaries. Add slashes where the pauses would be and the spacing comes back.

No. Input is uppercased before encoding because Morse has no concept of letter case. hello and HELLO produce the identical pattern, and decoded text always arrives in capitals.

A dash lasts three times as long as a dot. Gaps are one dot length between symbols, three between letters, and seven between words. This tool handles the symbols; the timing matters when you key the code as sound or light.

Type or paste your sentence in the input pane and press Text → Morse. Each letter turns into its dot dash pattern, and this english to morse code translator separates words with a slash so the reader can tell where one word ends. It's the quickest way to turn a note into signals for a practice drill.

Yes. Paste the dots and dashes, press Morse → Text, and the letters come back. As a morse code decoder it reads single spaces between letters and a slash between words, so a signal like ... --- ... returns SOS. That covers most puzzle answers and radio practice logs.

Yes. Once you decode, the output is ordinary letters, so morse code to english happens in the same step as morse code to text. There's no separate language setting; each pattern maps to its Latin letter, digit, or punctuation mark.

Yes, it's free and runs entirely in your browser with nothing to install. As a morse code decoder online it needs no account and no upload, so you can paste a signal, read the result, and close the tab. Your text never leaves your machine.

Yes. The morse code a to z mapping is complete, every letter from A as .- to Z as --.., plus the digits 0 to 9. So any English word encodes without gaps, and decoding returns each letter in capitals.

Each letter is built from just two marks, a short dot and a longer dash. So dot dot morse code, meaning two dots in a row, spells the letter I, while a single dot is E. The tool prints dots as periods and dashes as hyphens so they copy cleanly into any text field.

It's a solid practice aid. Type a word, see its pattern, then cover the output and try to write it from memory before checking. Working short messages both directions is how most people learn morse code faster than staring at a chart.

A forward slash marks the gap between morse code words, and single spaces mark the gap between letters. The decoder splits on those slashes first, so HI THERE comes across as two words rather than one long run of letters.

An operator tapped a key to make short and long pulses, and a receiver read them by sound or by marks on paper tape. Writing a message in morse code let it travel down a single wire long before voice could. This tool handles the letter mapping, while the timing and keying were the operator's craft.

Morse code isn't a language of its own; it's an encoding for the letters of whatever language you already write. Calling it a morse code language is common shorthand, but under the hood the tool just swaps each Latin character for a pattern of dots and dashes. Grammar and words stay exactly as you typed them.

Paste just that pattern and press Morse → Text, and the character it maps to is the meaning you're after. For example .-.. returns L. For a whole line, keep single spaces between letters so each one resolves on its own.

No. It reads typed dots and dashes, not sound, so it can't do morse code audio to text on its own. If you have a recording, listen and write out the beeps as dots and dashes first, then paste that in. There's no morse code sound to text step here, since the page never touches your microphone or audio files.